| PeterPaul

Series 20 Model MLV22 (REVERSE POLARITY)

Read more about Series 20 Model MLV22 (REVERSE POLARITY)

Series 20 Model MLV22 (REVERSE POLARITY) solenoid operator

DIN coil (2 terminals with ground) wiring diagram

Series 20 Model MLV22 (REVERSE POLARITY) flow diagram

This type of valve is often used in remote areas where continuous power may not be available or with battery-powered portable equipment where power capacity is limited, as it only uses power during latching and un-latching. It is also valuable in equipment where coil heating, due to continuous application of power, is undesirable. Air and other fluids are compatible with standard Buna seals. Hot water, steam, gasoline, oils, some hydraulic fluids, and many other media require special seal materials.

Neutral (−) a. Pulse Yellow lead to Positive (+) to latch b. Pulse Blue lead to Positive (+) to un-latch

Positive (+) a. Pulse Yellow lead to Neutral (−) to un-latch b. Pulse Blue lead to Neutral (−) to latch

VALVE SPECIFICATIONS

Valve specifications — Series 20 Model MLV22 (REVERSE POLARITY)
MAX. OPER.	ORIFICE SIZE	CV FACTOR	VALVE NUMBER DIN COIL (2 TERMINALS WITH GROUND)		VALVE NUMBER 2 WIRE COIL
PRESS. DIFF.			VALVE NUMBER DIN COIL (2 TERMINALS WITH GROUND)		VALVE NUMBER 2 WIRE COIL
DC			1/8 NPT PORTS	1/4 NPT PORTS	1/8 NPT PORTS	1/4 NPT PORTS

1000*	1/32	.024	22G7DELM-∆	22G9DELM-∆	22G7DGLM-∆	22G9DGLM-∆
500*	3/64	.052	22H7DELM-∆	22H9DELM-∆	22H7DGLM-∆	22H9DGLM-∆
400	1/16	.095	22J7DELM-∆	22J9DELM-∆	22J7DGLM-∆	22J9DGLM-∆
250	3/32	.156	22K7DELM-∆	22K9DELM-∆	22K7DGLM-∆	22K9DGLM-∆
200	1/8	.214	22N7DELM-∆	22N9DELM-∆	22N7DGLM-∆	22N9DGLM-∆
150	5/32	.404	22O7DELM-∆	22O9DELM-∆	22O7DGLM-∆	22O9DGLM-∆
50	3/16	.500	22P7DELM-∆	22P9DELM-∆	22P7DGLM-∆	22P9DGLM-∆
40	1/4	.700	22R7DELM-∆	22R9DELM-∆	22R7DGLM-∆	22R9DGLM-∆

* FKM seals not recommended for pressures of 500 psi and above.

Ordering Information:

Seal Material: Replace ∆ with desired code - Blank = Nitrile (Buna) S = Low Temp Buna. N = FKM* E = Neoprene A = EPDM

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (22J7DELM-∆ 12/DC) repair pack (K22NDL DC)

Coil Voltage

6, 9, 12, 24/DC

Nominal Power

DC — 10.0 Watts

Coil Construction

Molded Class B with DIN 43650 Form A Connector (Std.), Leadwires (Opt.) For your convenience we have the female DIN style mating connector No. 20-198** available for an additional fee.*

Typical Response Time on Air

Approximate 50 millisecond pulse to energize and de-energize.

Operating Speed

Up to 600 CPM

Internal Components

Stainless Steel

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Porting

Standard 1/8” and 1/4” NPT (other ports available).*

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Valve Weight

1.2 lb average

Repair Packs

See table above.

Options

Alternate Port Locations, Metering and Alternate Elastomers, Female DIN Style Connector Part Numbers DIN COIL (2 TERMINALS W/GROUND) #20-198 & DIN COIL (3 TERMINALS W/GROUND) #20-19102. Consult representative or factory for more options & specifications.

Media

Air and other fluids compatible with standard Buna seals. Hot water, steam, gasoline, oils, some hydraulic fluids, and many other media require special seal materials. (Series 20 pressure ratings may change due to the viscosity of the liquid.)*

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Burst Pressure

5000 PSI

Leakage

Bubble tight for standard valves.

Vacuum

To 5 Microns*

Flow Chart Series 20-30

Nomenclature Chart (non 58 series)

Series MLV20 Model 22 Magnetic Latching (Reverse Polarity)

Technical drawing — MODEL 22 1/4-18 NPT 2WNC MAGNETIC LATCHING DIN STYLE COIL — MODEL 22
1/4-18 NPT 2WNC MAGNETIC LATCHING DIN STYLE COIL

Technical drawing — MODEL 22 1/8-27 NPT 2WNC MAGNETIC LATCHING DIN STYLE COIL — MODEL 22
1/8-27 NPT 2WNC MAGNETIC LATCHING DIN STYLE COIL

Technical drawing — MODEL 22 METERING 2WNC MAGNETIC LATCHING DIN STYLE COIL — MODEL 22
METERING 2WNC MAGNETIC LATCHING DIN STYLE COIL

Technical drawing — MODEL 22 1/4-18 NPT 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL 22
1/4-18 NPT 2WNC MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 22 1/8-27 NPT 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL 22
1/8-27 NPT 2WNC MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 22 METERING 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL 22
METERING 2WNC MAGNETIC LATCHING COIL WITH LEADS

Stainless Steel (Std.) or Brass (Opt.)

Series 80 Model MLV828 (REVERSE POLARITY)

Read more about Series 80 Model MLV828 (REVERSE POLARITY)

Series 80 Model MLV828 (REVERSE POLARITY) - Brass

Series 80 Model MLV828 (REVERSE POLARITY) flow diagram

2-Way Large Orifice, Internally Piloted, Reverse Polarity Magnet Latching Valve - PeterPaul offers a line of large orifice solenoid valves to address process industry requirements for high flow rate or quick dump and fill capacity. These DC powered valves are also suited for gas and liquid applications. Port sizes for pilot lift, two-way normally closed versions range from 1/2” to 3” NPT, with pressure ratings from 3 to 200 PSI.

Large orifice sizes for high flow applications.
Body is made of brass forgings or 316 stainless steel.
Operates on differential pressure — internal pilot.
NPT threaded connections.
Same coils and housings as our popular 20 Series.

Neutral (−) a. Pulse Yellow lead to Positive (+) to latch b. Pulse Blue lead to Positive (+) to un-latch

Positive (+) a. Pulse Yellow lead to Neutral (−) to un-latch b. Pulse Blue lead to Neutral (−) to latch

VALVE SPECIFICATIONS

Valve specifications — Series 80 Model MLV828 (REVERSE POLARITY)
MAX. OPER. PRESS. DIFF.	MIN. OPER. PRESS. DIFF.	ORIFICE SIZE	CV FACTOR	PIPE SIZE	VALVE NUMBER 2 WIRE COIL	VALVE NUMBER DIN COIL
DC	MIN. OPER. PRESS. DIFF.	ORIFICE SIZE	CV FACTOR	PIPE SIZE	VALVE NUMBER 2 WIRE COIL	VALVE NUMBER DIN COIL

200	3	1/2	4.0	1/2 NPT	828B12DGLM-∆	828B12DELM-∆
200	3	3/4	5.8	3/4 NPT	828Y19DGLM-∆	828Y19DELM-∆
200	3	1	13.0	1 NPT	828D13DGLM-∆	828D13DELM-∆
200	3	1 1/2	29.0	1 1/2 NPT	828E14DGLM-∆	828E14DELM-∆
200	3	2	46.0	2 NPT	828F16DGLM-∆	828F16DELM-∆
200	3	3	76.0	2 1/2 NPT	828W17DGLM-∆	828W17DELM-∆
200	3	3	98.0	3 NPT	828W18DGLM-∆	828W18DELM-∆

* FKM seals not recommended for pressures of 500 psi and above.

Ordering Information:

Seal Material: Replace ∆ with desired code - Blank = Nitrile (Buna) S = Low Temp Buna. N = FKM* E = Neoprene A = EPDM

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (828B12DELM-∆ 12/DC) repair pack (K828BDL DC)

Coil Voltage

12, 24/DC

Nominal Power

DC — 10 Watts

Coil Construction

Molded

Typical Response Time on Air

Approximate 50 millisecond pulse to energize and de-energize.

Operating Speed

Up to 100 CPM

Internal Components

Stainless Steel (Std.)

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Repair Packs

See table above.

Options

Media

Air, water, and other fluids compatible with Buna seals. Hot water, steam, gasoline and many oils require special seal materials. Consult representative or factory. (Series 80 pressure ratings may change due to the viscosity of the liquid.)*

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Leakage

Bubble tight

Nomenclature Chart (non 58 series)

SERIES 80 MODEL MLV828 2WNC MAGNET LATCHING DIN COIL

Technical drawing — MODEL MLV828 1-1/2" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL — MODEL MLV828
1-1/2" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL

Technical drawing — MODEL MLV828 1/2" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL — MODEL MLV828
1/2" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL

Technical drawing — MODEL MLV828 1" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL — MODEL MLV828
1" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL

Technical drawing — MODEL MLV828 2-1/2" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL — MODEL MLV828
2-1/2" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL

Technical drawing — MODEL MLV828 2" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL — MODEL MLV828
2" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL

Technical drawing — MODEL MLV828 3/4" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL — MODEL MLV828
3/4" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL

Technical drawing — MODEL MLV828 3" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL — MODEL MLV828
3" NPT PORTS 2WNC MAGNETIC LATCHING DIN COIL

SERIES 80 MODEL 828 2WNC MAGNET LATCHING COIL WITH LEADS

Technical drawing — MODEL MLV828 1-1/2" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL MLV828
1-1/2" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL MLV828 1/2" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL MLV828
1/2" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL MLV828 1" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL MLV828
1" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL MLV828 2-1/2" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL MLV828
2-1/2" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL MLV828 2" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL MLV828
2" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL MLV828 3/4" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL MLV828
3/4" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL MLV828 3" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS — MODEL MLV828
3" NPT PORTS 2WNC MAGNETIC LATCHING COIL WITH LEADS

Brass (Std.) — Stainless Steel (Opt.)

Series 20 Model MLV23 (REVERSE POLARITY) - Exhaust to Atmosphere

Read more about Series 20 Model MLV23 (REVERSE POLARITY) - Exhaust to Atmosphere

Series 20 Model MLV23 (REVERSE POLARITY) - Exhaust to Atmosphere solenoid operator

Series 20 Model MLV23 (REVERSE POLARITY) - Exhaust to Atmosphere flow diagram

3-Way Normally Closed Magnet Latching Valve — Exhaust to Atmosphere - This type of valve is often used in remote areas where continuous power may not be available or with battery-powered portable equipment where power capacity is limited. It is also valuable in equipment where coil heating, due to continuous application of power, is undesirable. Air and other fluids are compatible with standard Buna seals. Hot water, steam, gasoline, oils, some hydraulic fluids, and many other media require special seal materials.

Valve is magnetic latching.
Meets today's demand for economy of space.
Uses power only during latching and un-latching.
Great for medical and chemical analyzers.

Neutral (−) a. Pulse Yellow lead to Positive (+) to latch b. Pulse Blue lead to Positive (+) to un-latch

Positive (+) a. Pulse Yellow lead to Neutral (−) to un-latch b. Pulse Blue lead to Neutral (−) to latch

VALVE SPECIFICATIONS

Valve specifications — Series 20 Model MLV23 (REVERSE POLARITY) - Exhaust to Atmosphere
MAX. OPER.	ORIFICE SIZE		CV FACTOR		VALVE NUMBER DIN COIL (2 TERMINALS WITH GROUND)		VALVE NUMBER 2 WIRE COIL
PRESS. DIFF.	ORIFICE SIZE		CV FACTOR		VALVE NUMBER DIN COIL (2 TERMINALS WITH GROUND)		VALVE NUMBER 2 WIRE COIL
DC	INLET	EXH	INLET	EXH	1/8 NPT PORTS	1/4 NPT PORTS	1/8 NPT PORTS	1/4 NPT PORTS

400	1/32	1/32	.024	.024	23GG7DELM-∆	23GG9DELM-∆	23GG7DGLM-∆	23GG9DGLM-∆
150	3/64	1/16	.052	.095	23HJ7DELM-∆	23HJ9DELM-∆	23HJ7DGLM-∆	23HJ9DGLM-∆
100	1/16	1/16	.095	.095	23JJ7DELM-∆	23JJ9DELM-∆	23JJ7DGLM-∆	23JJ9DGLM-∆
100	1/16	3/32	.095	.156	23JK7DELM-∆	23JK9DELM-∆	23JK7DGLM-∆	23JK9DGLM-∆
75	3/32	3/32	.156	.156	23KK7DELM-∆	23KK9DELM-∆	23KK7DGLM-∆	23KK9DGLM-∆
50	1/8	3/32	.214	.156	23NK7DELM-∆	23NK9DELM-∆	23NK7DGLM-∆	23NK9DGLM-∆
20	3/16	3/32	.500	.156	23PK7DELM-∆	23PK9DELM-∆	23PK7DGLM-∆	23PK9DGLM-∆

* FKM seals not recommended for pressures of 500 psi and above.

Ordering Information:

Seal Material: Replace ∆ with desired code - Blank = Nitrile (Buna) S = Low Temp Buna. N = FKM* E = Neoprene A = EPDM

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (23JJ7DELM-∆ 12/DC) repair pack (K23JJDL DC)

Coil Voltage

6, 9, 12, 24/DC

Nominal Power

DC — 10.0 Watts

Coil Construction

Molded Class B with DIN 43650 Form A Connector (Std.), Leadwires (Opt.) For your convenience we have the female DIN style mating connector No. 20-198** available for an additional fee.*

Typical Response Time on Air

Approximate 50 millisecond pulse to energize and de-energize.

Operating Speed

Up to 600 CPM

Internal Components

Stainless Steel

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Porting

Standard 1/8” and 1/4” NPT (other ports available).*

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Valve Weight

1.2 lb average

Repair Packs

See table above.

Options

Media

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Burst Pressure

5000 PSI

Leakage

Bubble tight for standard valves.

Vacuum

To 5 Microns*

Flow Chart Series 20-30

Nomenclature Chart (non 58 series)

Series MLV20 Model 23 Magnetic Latching (Reverse Polarity) — Exhaust to Atmosphere

Technical drawing — MODEL 23 1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL — MODEL 23
1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL

Technical drawing — MODEL 23 1/8-27 NPT 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL — MODEL 23
1/8-27 NPT 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL

Technical drawing — MODEL 23 BODY OPTION "E" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL — MODEL 23
BODY OPTION "E" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL

Technical drawing — MODEL 23 BODY OPTION "O" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL — MODEL 23
BODY OPTION "O" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL

Technical drawing — MODEL 23 BODY OPTION "R" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL — MODEL 23
BODY OPTION "R" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL

Technical drawing — MODEL 23 METERING 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL — MODEL 23
METERING 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL

Technical drawing — MODEL 23 1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS — MODEL 23
1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 23 1/8-27 NPT 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS — MODEL 23
1/8-27 NPT 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 23 BODY OPTION "E" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS — MODEL 23
BODY OPTION "E" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 23 BODY OPTION "O" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS — MODEL 23
BODY OPTION "O" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 23 BODY OPTION "R" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS — MODEL 23
BODY OPTION "R" 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 23 METERING 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS — MODEL 23
METERING 3WNC EXHAUST TO ATMOSPHERE MAGNETIC LATCHING COIL WITH LEADS

Stainless Steel (Std.) or Brass (Opt.)

Series 70 Model N73 - Piped Exhaust

Read more about Series 70 Model N73 - Piped Exhaust

Series 70 Model N73 - Piped Exhaust flow diagram

The N70 line PeterPaul Hazardous Location valves are UL listed and certified for non-incendive Hazardous Location Class 1, Div 2, Groups A, B, C and D; Class 2, Div 2, Groups E, F and G; T3C temperature rating.

Largest direct acting non-piloted valve we manufacture.
Large orifice.
High flow.
Will operate effectively at very low pressures or vacuum.

VALVE SPECIFICATIONS

Valve specifications — Series 70 Model N73 - Piped Exhaust
MAX. OPER. PRESS. DIFF.		ORIFICE SIZE		CV FACTOR		NORTH AMERICAN VALVE NUMBER CONDUIT HOUSING
AC	DC	INLET	EXH	INLET	EXH	1/4 NPT PORTS

350	350	1/16	1/16	.09	.09	N73JJ9ZCP
250	250	3/32	3/32	.22	.22	N73KK9ZCP
175	175	1/8	1/8	.35	.35	N73NN9ZCP
125	125	5/32	5/32	.45	.45	N73OO9ZCP
100	100	3/16	3/16	.50	.50	N73PP9ZCP
50	50	1/4	3/16	.78	.50	N73RP9ZCP

Ordering Information:

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (N73OO9ZCP 120/60) repair pack (KN73OOX AC)

When ordering operators add the letter “O” to the front of the valve number, replace body port number with the letter “D”: example: operator (ON73OODZCP 120/60)

Coil Voltage

12/DC, 24/DC, 48/DC, 125/DC, 120/60-110/50, 240/60, and 24/60.

Nominal Power

AC — 18.0 Watts DC — 16.0 Watts

Coil Construction

Potted Class F. (Class H optional)

Typical Response Time on Air

4 - 16 Milliseconds

Operating Speed

Up to 600 CPM

Duty Cycle

Continuous

Internal Components

Stainless Steel. Copper – AC Only.

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Porting

Standard 1/4" NPT (other ports available).*

Housing

1/2′′ NPT conduit*

Listings

Listed and Certified for Non-Incendive Hazardous Locations Class 1, Div 2, Groups A, B, C and D; Class 2, Div 2, Groups E, F and G; T3C Temperature rating.*

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Valve Weight

Conduit Valve: 2.06 lb

Repair Packs

See table above.

Options

Alternate Port Locations, Metering and Alternate Elastomers * Consult representative or factory for options and specifications.

Media

Air, water, and other fluids compatible with standard Buna seals. Hot water, steam, gasoline, and many oils require special seal materials. (Series 70 pressure ratings may change due to the viscosity of the liquid.)*

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Burst Pressure

4000 PSI

Leakage

Bubble tight for standard valves.

Vacuum

To 5 Microns*

Flow Chart Series 70

Nomenclature Chart (non 58 series)

Series 70 HAZARDOUS LOCATION VALVES

Technical drawing — MODEL N73 1/4-18 NPT 3WNC CONDUIT CONNECTION — MODEL N73
1/4-18 NPT 3WNC CONDUIT CONNECTION

Technical drawing — MODEL N73 1/4-18 NPT 3WNC CONDUIT/BRACKET CONNECTION — MODEL N73
1/4-18 NPT 3WNC CONDUIT/BRACKET CONNECTION

Stainless Steel (Std.) or Brass (Opt.)

Certification

North American

Series E50 Model E53 - Piped Exhaust

Read more about Series E50 Model E53 - Piped Exhaust

Series E50 Model E53 - Piped Exhaust flow diagram

PeterPaul explosion proof valves are used where fire or explosion hazards exist due to the presence of flammable gases or vapors, flammable liquids, combustible dust, or easily ignitable fibers. Hazardous Location valves are recommended, or in some cases compulsory, where a high level of protection from explosion is required.

Miniature Hazardous Location valve.
Flame-proof construction.
High quality engineering.

Valve specifications — Series E50 Model E53 - Piped Exhaust
MAX. OPER. PRESS. DIFF.		ORIFICE SIZE		CV FACTOR		NORTH AMERICAN VALVE NUMBER
AC	DC	INLET	EXH	INLET	EXH	NORTH AMERICAN VALVE NUMBER

200	200	1/32	1/32	.022	.020	E53GG8XCCM-∆
150	150	3/64	3/64	.055	.048	E53HH8XCCM-∆
150	150	3/64	1/16	.055	.075	E53HJ8XCCM-∆
100	100	1/16	1/16	.075	.075	E53JJ8XCCM-∆
60	60	3/32	1/16	.156	.075	E53KJ8XCCM-∆
50	50	3/32	3/32	.156	.156	E53KK8XCCM-∆
30	30	1/8	1/16	.230	.075	E53NJ8XCCM-∆
30	30	1/8	3/32	.230	.156	E53NK8XCCM-∆

Ordering Information:

Seal Material: Replace ∆ with desired code - Blank = Nitrile (Buna) S = Low Temp Buna. N = FKM* E = Neoprene A = EPDM

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (E53HJ8XCCM 120/60) repair pack (5KE53HJX AC)

When ordering operators add the letter “O” to the front of the valve number, replace body port number with the letter “D”: example: operator (OE53HJDXCCM 120/60)

Coil Voltage

12/DC, 24/DC, 48/DC, 125/DC, 120/60-110/50, 240/60, and 24/60.

Nominal Power

AC — 5.6 Watts DC — 7.2 Watts

Coil Construction

Molded Class F with third wire ground (Std.), Class H or Potted (Opt.)

Typical Response Time on Air

4 - 16 Milliseconds

Operating Speed

Up to 600 CPM

Duty Cycle

Continuous

Internal Components

Stainless Steel. Copper – AC Only.

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Porting

1/8" NPT (Std.)

Housing

Flame-Proof construction with 1/2" NPT conduit

Listings

Valves are UL listed and CSA certified for Hazardous Locations — Class I, Div 1, Group C and D - Class II, Div 1, Groups E, F, and G; Div 2, Groups A, B, C, D, E, F, and G

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Valve Weight

0.65 lbs

Repair Packs

See table above.

Options

Alternate Port Locations, Metering, Alternate Elastomers, All Stainless Steel Construction*

Media

Air, and other fluids compatible with standard Buna seals. Hot water, steam, gasoline, oils, some hydraulic fluids, and many media require special seal materials. (Series 50 pressure ratings may change due to the viscosity of the liquid.)*

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Burst Pressure

5000 PSI

Leakage

Bubble tight for standard valves.

Vacuum

To 5 Microns*

Flow Chart Series 40-50

Nomenclature Chart (non 58 series)

Series E50 Hazardous Location Valves

Technical drawing — MODEL E53 1/8-27 NPT 3WNC PIPED EXHAUST EXPLOSION PROOF — MODEL E53
1/8-27 NPT 3WNC PIPED EXHAUST EXPLOSION PROOF

Technical drawing — MODEL E53 10-32 PORTS 3WNC PIPED EXHAUST EXPLOSION PROOF — MODEL E53
10-32 PORTS 3WNC PIPED EXHAUST EXPLOSION PROOF

Technical drawing — MODEL E53 BODY OPTION "E" 3WNC PIPED EXHAUST EXPLOSION PROOF — MODEL E53
BODY OPTION "E" 3WNC PIPED EXHAUST EXPLOSION PROOF

Technical drawing — MODEL E53 BODY OPTION "O" 3WNC PIPED EXHAUST EXPLOSION PROOF — MODEL E53
BODY OPTION "O" 3WNC PIPED EXHAUST EXPLOSION PROOF

Technical drawing — MODEL E53 BODY OPTION "R" 3WNC PIPED EXHAUST EXPLOSION PROOF — MODEL E53
BODY OPTION "R" 3WNC PIPED EXHAUST EXPLOSION PROOF

Technical drawing — MODEL E53 METERED BODY 3WNC PIPED EXHAUST EXPLOSION PROOF — MODEL E53
METERED BODY 3WNC PIPED EXHAUST EXPLOSION PROOF

Stainless Steel (Std.)

Series 50 Operators Explosion Proof

Technical drawing — MODEL OE53 3WNC PIPED EXHAUST EXPLOSION PROOF — MODEL OE53 3WNC PIPED EXHAUST EXPLOSION PROOF

Certification

North American

Series 70 Model 73 - Exhaust to Atmosphere

Read more about Series 70 Model 73 - Exhaust to Atmosphere

Series 70 Model 73 - Exhaust to Atmosphere solenoid operator

Series 70 Model 73 - Exhaust to Atmosphere flow diagram

Super valves that have ratings that formerly required valves of much greater size. Air, water, and other fluids are compatible with standard Buna seals. Hot water, steam, gasoline, and many oils require special seal materials.

Largest direct acting non-piloted valve we manufacture.
Large orifice.
High flow.
Will operate effectively at very low pressures or vacuum.

Valve specifications — Series 70 Model 73 - Exhaust to Atmosphere
MAX. OPER. PRESS. DIFF.		ORIFICE SIZE		CV FACTOR		VALVE NUMBER GROMMET HOUSING	VALVE NUMBER CONDUIT HOUSING
AC	DC	INLET	EXH	INLET	EXH	1/4 NPT PORTS	1/4 NPT PORTS

350	350	1/16	1/16	.09	.09	73JJ9DGM	73JJ9DCM
250	250	3/32	3/32	.22	.22	73KK9DGM	73KK9DCM
175	175	1/8	1/8	.35	.35	73NN9DGM	73NN9DCM
125	125	5/32	5/32	.45	.45	73OO9DGM	73OO9DCM
100	100	3/16	3/16	.50	.50	73PP9DGM	73PP9DCM
50	50	1/4	3/16	.78	.50	73RP9DGM	73RP9DCM

Ordering Information:

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (73OO9DGM 120/60) repair pack (K73OOD AC)

When ordering operators add the letter “O” to the front of the valve number, replace body port number with the letter “D”: example: operator (O73OODDGM 120/60)

Coil Voltage

12/DC, 24/DC, 48/DC, 125/DC, 120/60-110/50, 240/60, and 24/60.

Nominal Power

AC — 18.0 Watts DC — 16.0 Watts

Coil Construction

Molded Class F (Std.), Potted and Class H Option

Typical Response Time on Air

4 - 16 Milliseconds

Operating Speed

Up to 600 CPM

Duty Cycle

Continuous

Internal Components

Stainless Steel. Copper – AC Only.

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Porting

Standard 1/4" NPT (other ports available).*`

Housing

Grommet and 1/2″ NPT conduit – many options available.*

Listings

Most valves are UL and CSA listed.*

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Valve Weight

Grommet Valve: 2.00 lb Conduit Valve: 2.06 lb

Repair Packs

See table above.

Options

Alternate Port Locations, Metering and Alternate Elastomers * Consult representative or factory for options and specifications.

Media

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Burst Pressure

4000 PSI

Leakage

Bubble tight for standard valves.

Vacuum

To 5 Microns*

Flow Chart Series 70

Nomenclature Chart (non 58 series)

Series 70 3WNC EXHAUST TO ATMOSPHERE DIN STYLE COIL

Technical drawing — MODEL 73 3WNC EXHAUST TO ATMOSPHERE DIN STYLE COIL — MODEL 73 3WNC EXHAUST TO ATMOSPHERE DIN STYLE COIL

Series 70 General Purpose Valves Conduit

Technical drawing — MODEL 73 1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE CONDUIT CONNECTION — MODEL 73
1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE CONDUIT CONNECTION

Series 70 General Purpose Valves Grommet

Technical drawing — MODEL 73 1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE GROMMET WITH LEADS — MODEL 73
1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE GROMMET WITH LEADS

Series 70 General Purpose Valves Grommet/Bracket Connection

Technical drawing — MODEL 73 1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE GROMMET/BRACKET CONNECTION — MODEL 73
1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE GROMMET/BRACKET CONNECTION

Series 70 General Purpose Valves Conduit/Bracket Connection

Technical drawing — MODEL 73 1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE CONDUIT/BRACKET CONNECTION — MODEL 73
1/4-18 NPT 3WNC EXHAUST TO ATMOSPHERE CONDUIT/BRACKET CONNECTION

Stainless Steel (Std.) or Brass (Opt.)

Series 70 Operators Conduit

Technical drawing — MODEL O73 3WNC EXHAUST TO ATMOSPHERE CONDUIT CONNECTION — MODEL O73 3WNC EXHAUST TO ATMOSPHERE CONDUIT CONNECTION

Series 70 Operators Conduit/Bracket Connection

Technical drawing — MODEL O73 3WNC EXHAUST TO ATMOSPHERE CONDUIT/BRACKET CONNECTION — MODEL O73 3WNC EXHAUST TO ATMOSPHERE CONDUIT/BRACKET CONNECTION

Series 70 Operators Grommet

Technical drawing — MODEL O73 3WNC EXHAUST TO ATMOSPHERE GROMMET HOUSING WITH LEADS — MODEL O73 3WNC EXHAUST TO ATMOSPHERE GROMMET HOUSING WITH LEADS

Series 70 Operators Grommet/Bracket Connection

Technical drawing — MODEL O73 3WNC EXHAUST TO ATMOSPHERE GROMMET/BRACKET HOUSING WITH LEADS — MODEL O73 3WNC EXHAUST TO ATMOSPHERE GROMMET/BRACKET HOUSING WITH LEADS

Series 70 Model N74

Read more about Series 70 Model N74

The 70 line PeterPaul Hazardous Location valves are UL listed and certified for non-incendive Hazardous Locations — Class I, Div 2, Groups A, B, C and D; Class II, Div 2, Groups E, F and G; T3C temperature rating.

Largest direct acting non-piloted valve we manufacture.
Large orifice.
High flow.
Will operate effectively at very low pressures or vacuum.

Valve specifications — Series 70 Model N74
MAX. OPER. PRESS. DIFF.		ORIFICE SIZE		CV FACTOR		NORTH AMERICAN VALVE NUMBER CONDUIT HOUSING
AC	DC	INLET	EXH	INLET	EXH	1/4 NPT PORTS

350	350	1/16	1/16	.09	.09	N74JJ9ZCP
250	250	3/32	3/32	.22	.22	N74KK9ZCP
175	175	1/8	1/8	.35	.35	N74NN9ZCP
125	125	5/32	5/32	.45	.45	N74OO9ZCP
100	100	3/16	3/16	.50	.50	N74PP9ZCP

Ordering Information:

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (N74PP9ZCP 120/60) repair pack (KN74PPX AC)

When ordering operators add the letter “O” to the front of the valve number, replace body port number with the letter “D”: example: operator (ON74PPDZCP 120/60)

Coil Voltage

12/DC, 24/DC, 48/DC, 125/DC, 120/60-110/50, 240/60, and 24/60.

Nominal Power

AC — 18.0 Watts DC — 16.0 Watts

Coil Construction

Potted Class F. (Class H optional)

Typical Response Time on Air

4 - 16 Milliseconds

Operating Speed

Up to 600 CPM

Duty Cycle

Continuous

Internal Components

Stainless Steel. Copper – AC Only.

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Porting

Standard 1/4" NPT (other ports available).*

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Valve Weight

Conduit Valve: 2.06 lb

Repair Packs

See table above.

Options

Alternate Port Locations, Metering and Alternate Elastomers * Consult representative or factory for options and specifications.

Media

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Burst Pressure

4000 PSI

Leakage

Bubble tight for standard valves.

Vacuum

To 5 Microns*

Flow Chart Series 70

Nomenclature Chart (non 58 series)

Series 70 HAZARDOUS LOCATION VALVES

Technical drawing — MODEL N74 1/4-18 NPT 3WNO CONDUIT CONNECTION — MODEL N74
1/4-18 NPT 3WNO CONDUIT CONNECTION

Technical drawing — MODEL N74 1/4-18 NPT 3WNO CONDUIT/BRACKET CONNECTION — MODEL N74
1/4-18 NPT 3WNO CONDUIT/BRACKET CONNECTION

Stainless Steel (Std.) or Brass (Opt.)

Certification

North American

Series EL50 Model EL51

Read more about Series EL50 Model EL51

Miniature Hazardous Location valves using even less power than an E51.
Flame-Proof construction.
High quality engineering.

Valve specifications — Series EL 50 Model EL51
MAX. OPER. PRESS. DIFF.		ORIFICE SIZE	CV FACTOR	NORTH AMERICAN VALVE NUMBER
AC	DC	ORIFICE SIZE	CV FACTOR	NORTH AMERICAN VALVE NUMBER

200	200	1/32	.020	EL51G8XCCM-∆
120	120	3/64	.048	EL51H8XCCM-∆
50	50	1/16	.075	EL51J8XCCM-∆

Ordering Information:

Seal Material: Replace ∆ with desired code - Blank = Nitrile (Buna) S = Low Temp Buna. N = FKM* E = Neoprene A = EPDM

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (EL51H8XCCM 120/60) repair pack (5KEL51H AC)

When ordering operators add the letter “O” to the front of the valve number, replace body port number with the letter “D”: example: operator (OEL51HDXCCM 120/60)

Coil Voltage

12/DC, 24/DC, 48/DC, 125/DC, 120/60-110/50, 240/60, and 24/60.

Nominal Power

AC — 1.8 Watts DC — 1.8 Watts

Coil Construction

Molded Class F with third wire ground (Std.), Class H or Potted (Opt.)

Typical Response Time on Air

4 - 16 Milliseconds

Operating Speed

Up to 600 CPM

Duty Cycle

Continuous

Internal Components

Stainless Steel. Copper – AC Only.

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Porting

1/8" NPT (Std.)

Housing

Flame-Proof construction with 1/2" NPT conduit

Listings

Valves are UL listed and CSA certified for Hazardous Locations — Class I, Div 1, Group C and D - Class II, Div 1, Groups E, F, and G: Div 2, Groups A, B, C, D, E, F, and G.

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Valve Weight

0.65 lbs

Repair Packs

See table above.

Options

Alternate Port Locations, Metering, Alternate Elastomers and All Stainless Steel Construction*

Media

Air and other common gases and common refrigerants except ammonia, city gas supplies by public utilities, Nos. 1 and 2 fuel oils, oils having viscosities not more than 40, SU at 100°F, steam, some hydraulic and water or other aqueous non-flammable liquids

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Burst Pressure

4000 PSI

Leakage

Bubble tight for standard valves.

Vacuum

To 5 Microns*

Flow Chart Series 40-50

Nomenclature Chart (non 58 series)

Series EL 50 Hazardous Location Valves

Technical drawing — MODEL EL51 1/8-27 NPT 2WNO EXPLOSION PROOF — MODEL EL51
1/8-27 NPT 2WNO EXPLOSION PROOF

Technical drawing — MODEL EL51 BODY OPTION "O" 2WNO EXPLOSION PROOF — MODEL EL51
BODY OPTION "O" 2WNO EXPLOSION PROOF

Stainless Steel (Std.)

Series 50 Operators Explosion Proof

Technical drawing — MODEL OEL51 2WNO EXPLOSION PROOF — MODEL OEL51 2WNO EXPLOSION PROOF

Certification

North American

Series 80 Model E828 C/I Rated

Read more about Series 80 Model E828 C/I Rated

Series 80 Model E828 C/I Rated flow diagram

PeterPaul offers a line of Hazardous Location rated, large orifice Automatic Safety Shut Off Valves designed specifically for gas appliances. These valves meet the standards for Commercial/Industrial (C/I) Safety Shut Off Valves per ANSI Z21.21 (CSA 6.5). They are well suited for use in heating equipment, furnaces, ovens, kilns, boilers and gas generators.

Large orifice sizes for high capacity.
Body is made of 316 stainless steel.
Potted coil for outdoor service.
Pilot operated.
Voltages: 120/60, 12/DC and 24/DC
Power Input: 1.8 watts
Rated for ambient temperatures of -40°C to +65°C
NPT threaded connections.

Valve specifications — Series 80 Model E828 C/I Rated
MAX. OPER. PRESS. DIFF.		MIN. OPER. PRESS. DIFF.	GAS CAPACITY BTU/Hr	CV FACTOR	PIPE SIZE	NORTH AMERICAN VALVE NUMBER
AC	DC	MIN. OPER. PRESS. DIFF.	N.C.	N.C.	PIPE SIZE	NORTH AMERICAN VALVE NUMBER

30	30	3	7,575,000	13.0	1 NPT	E828D23DCCP-S

Ordering Information:

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (E828D23DCCP-S 24/DC) solenoid repair kit (80-30043-DC or 80-30043-AC) body repair kit (80-30045 for 1")

No operator available

Coil Voltage

120/60 and 12, 24/DC

Nominal Power

1.8 Watts

Coil Construction

Potted Class F

Operating Speed

Up to 100 CPM

Duty Cycle

Continuous

Internal Components

Stainless Steel. Copper – AC Only.

Elastomers

Nitrile (Buna)

Orifice Diameter

See table above.

Porting

1/2" NPT conduit

Listings

Valves are UL listed and CSA certified for Hazardous Locations — Class I, Div 1, Group C and D - Class II, Div 1, Groups E, F, and G; Div 2, Groups A, B, C, D, E, F, and G

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Repair Packs

See table above.

Media

Fuel Gas

Valve Temperature Range

– 40°F (-40°C) to 150°F (65°C) ambient and media.

Maximum Operating Pressure Differentials

See table above.

Leakage

Bubble tight

Series 80 Internal Pilot Valve - Explosion Proof Housing

Technical drawing — MODEL E828 1" NPT PORTS 2WNC EXPLOSION PROOF — MODEL E828
1" NPT PORTS 2WNC EXPLOSION PROOF

316 Stainless Steel

Certification

North American

Series 20 Model MLV26 (REVERSE POLARITY)

Read more about Series 20 Model MLV26 (REVERSE POLARITY)

Series 20 Model MLV26 (REVERSE POLARITY) solenoid operator

Series 20 Model MLV26 (REVERSE POLARITY) flow diagram

3-Way Multi-Purpose Reverse Polarity Magnet Latching Valve - This type of valve is often used in remote areas where continuous power may not be available or with battery-powered portable equipment where power capacity is limited. It is also valuable in equipment where coil heating, due to continuous application of power, is undesirable. Air and other fluids are compatible with standard Buna seals. Hot water, steam, gasoline, oils, some hydraulic fluids, and many other media require special seal materials.

Valve is magnetic latching.
Meets today's demand for economy of space.
Uses power only during latching and un-latching.
Great for medical and chemical analyzers.

Neutral (-) a. Pulse Yellow lead to Positive (+) to latch b. Pulse Blue lead to Positive (+) to un-latch

Positive (+) a. Pulse Yellow lead to Neutral (-) to un-latch b. Pulse Blue lead to Neutral (-) to latch

VALVE SPECIFICATION

Valve specifications — Series 20 Model MLV26 (REVERSE POLARITY)
MAX. OPER.	ORIFICE SIZE		CV FACTOR		VALVE NUMBER DIN COIL (2 TERMINALS WITH GROUND)		VALVE NUMBER 2 WIRE COIL
PRESS. DIFF.	ORIFICE SIZE		CV FACTOR		VALVE NUMBER DIN COIL (2 TERMINALS WITH GROUND)		VALVE NUMBER 2 WIRE COIL
DC	N.C.	N.O.	N.C.	N.O.	1/8 NPT PORTS	1/4 NPT PORTS	1/8 NPT PORTS	1/4 NPT PORTS

400	1/32	1/32	.024	.024	26GG7XELM-∆	26GG9ZELM-∆	26GG7XGLM-∆	26GG9ZGLM-∆
150	3/64	3/64	.052	.052	26HH7XELM-∆	26HH9ZELM-∆	26HH7XGLM-∆	26HH9ZGLM-∆
100	1/16	1/16	.095	.095	26JJ7XELM-∆	26JJ9ZELM-∆	26JJ7XGLM-∆	26JJ9ZGLM-∆
75	3/32	3/32	.156	.156	26KK7XELM-∆	26KK9ZELM-∆	26KK7XGLM-∆	26KK9ZGLM-∆

* FKM seals not recommended for pressures of 500 psi and above.

Ordering Information:

Seal Material: Replace ∆ with desired code - Blank = Nitrile (Buna) S = Low Temp Buna. N = FKM* E = Neoprene A = EPDM

When ordering valves or repair packs add voltage and frequency to complete valve number. For example: valve (26JJ7XELM-∆ 12/DC) repair pack (K26JJXL DC)

Coil Voltage

6, 9, 12, 24/DC

Nominal Power

DC — 10.0 Watts

Coil Construction

Molded Class B with DIN 43650 Form A Connector (Std.), Leadwires (Opt.) For your convenience we have the female DIN style mating connector No. 20-198** available for an additional fee.*

Typical Response Time on Air

Approximate 50 millisecond pulse to energize and de-energize.

Operating Speed

Up to 600 CPM

Internal Components

Stainless Steel

Elastomers

Nitrile (Buna) (Std.). Many other elastomers available.*

Orifice Diameter

See table above.

Porting

Standard 1/8” and 1/4” NPT (other ports available).*

Life Expectancy

Millions of cycles, depending on application, lubrication, etc.

Valve Weight

1.2 lb average

Repair Packs

See table above.

Options

Media

Valve Temperature Range

Standard Valves – 0°F (-18°C) to 104°F (40°C) ambient; 0°F (-18°C) to 150°F (65°C) media. Optional Valves – can tolerate much higher or much lower ambient and media temperatures.*

Maximum Operating Pressure Differentials

See table above.

Burst Pressure

5000 PSI

Leakage

Bubble tight for standard valves.

Vacuum

To 5 Microns*

Flow Chart Series 20-30

Nomenclature Chart (non 58 series)

Series MLV20 Model 26 Magnetic Latching (Reverse Polarity)

Technical drawing — MODEL 26 1/4-18 NPT 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL — MODEL 26
1/4-18 NPT 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL

Technical drawing — MODEL 26 1/8-27 NPT 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL — MODEL 26
1/8-27 NPT 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL

Technical drawing — MODEL 26 BODY OPTION "E" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL — MODEL 26
BODY OPTION "E" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL

Technical drawing — MODEL 26 BODY OPTION "O" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL — MODEL 26
BODY OPTION "O" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL

Technical drawing — MODEL 26 BODY OPTION "R" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL — MODEL 26
BODY OPTION "R" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL

Technical drawing — MODEL 26 METERING 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL — MODEL 26
METERING 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL

Technical drawing — MODEL 26 1/4-18 NPT 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS — MODEL 26
1/4-18 NPT 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 26 1/8-27 NPT 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS — MODEL 26
1/8-27 NPT 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 26 BODY OPTION "E" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS — MODEL 26
BODY OPTION "E" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 26 BODY OPTION "O" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS — MODEL 26
BODY OPTION "O" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 26 BODY OPTION "R" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS — MODEL 26
BODY OPTION "R" 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS

Technical drawing — MODEL 26 METERING 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS — MODEL 26
METERING 3-WAY MULTI-PURPOSE MAGNETIC LATCHING COIL WITH LEADS

Stainless Steel (Std.) or Brass (Opt.)

Subscribe to